User Tools

Site Tools


information_for_astronomers:user_guide:tutorials:4mtelescope

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
information_for_astronomers:user_guide:tutorials:4mtelescope [2018/09/18 10:41]
schweikert [Bugs]
information_for_astronomers:user_guide:tutorials:4mtelescope [2018/09/18 11:43] (current)
schweikert [Bugs]
Line 130: Line 130:
  
   * __**Telescope still not moving, optionally giving error messages**__   * __**Telescope still not moving, optionally giving error messages**__
-If a crossscan was started close to the hardcoded Azimuth endpoints of the telescope, it is possible that the telescope crossed over this endpoint. This means the actuator controls will have to be manually restarted ​by technician.+If a crossscan was started close to the hardcoded Azimuth endpoints of the telescope, it is possible that the telescope crossed over this endpoint. This means the actuator controls will have to be manually restarted ​take look at section Limitposition exceeded (F6029 Lagegrenzwert überschritten).
  
   * __**Multiple backends online at the same time, don't turn off on restart**__   * __**Multiple backends online at the same time, don't turn off on restart**__
Line 149: Line 149:
 {{ :​information_for_astronomers:​user_guide:​tutorials:​indraworksfoundhardware.png?​500 |}} {{ :​information_for_astronomers:​user_guide:​tutorials:​indraworksfoundhardware.png?​500 |}}
  
-If you connect ​to the hardware, the following window appears. Select the unit. +If you connect the hardware, the following window appears. Select the unit. 
  
 (134.104.79.88 -> Elevation) (134.104.79.88 -> Elevation)
Line 169: Line 169:
 __**Attention:​**__ __**Attention:​**__
  
-Both Achsstatus must show  „A0012 Steuer- und Leistungsteil betriebsbereit“. In addition it's only possible to communicate with the IndraWorks ​Ds or with the Controlsystem. If you want to control the teleskop with the Controlprogram ​you need do close IndraWorks ​Ds.+Both Achsstatus must show  „A0012 Steuer- und Leistungsteil betriebsbereit“. In addition it's only possible to communicate with the IndraWorks ​__or__ ​with the controlsystem. If you want to control the teleskop with the controlprogram ​you need to close IndraWorks.
  
-  * __**Limit Position ​exceeded (F6029 Lagegrenzwert überschritten)**__+  * __**Limitposition ​exceeded (F6029 Lagegrenzwert überschritten)**__
  
-Open IndraWorks ​Ds and search the units. __**Attention:​**__ You need to close the controlsystem ​if you open IndraWorks, because it's only possible to communicate with Indraworks ​__or__ the controlsystem.+Open IndraWorks and search the units. __**Attention:​**__ You need to close the controlsystem,​ because it's only possible to communicate with IndraWorks ​__or__ the controlsystem.
  
 Choose the unit: Choose the unit:
 +
 (134.104.79.88 -> Elevation) (134.104.79.88 -> Elevation)
  
 (134.104.79.89 -> Azimut) (134.104.79.89 -> Azimut)
  
-Delete the error:+Delete the error. After deleting the error the Achsstatus should show „A0012 Steuer- und Leistungsteil betriebsbereit“.
 {{ :​information_for_astronomers:​user_guide:​tutorials:​endlage.png?​500 |}} {{ :​information_for_astronomers:​user_guide:​tutorials:​endlage.png?​500 |}}
 +
 +Push "Start Easy-Startup-Modus"​ and "​Freigabe"​.
 +{{ :​information_for_astronomers:​user_guide:​tutorials:​start.png?​500 |}}
 +
 +__**Attention:​**__ Now you drive without any position limits!! Take care that you drive in the correct direction!!
 +{{ :​information_for_astronomers:​user_guide:​tutorials:​fahre.png?​500 |}}
 +
 +If the telescope is out of the position limit press the button "​Antrieb AUS" and then "Stop Easy-Startup-Modus"​. __The Achsstatus must show „A0012 Steuer- und Leistungsteil betriebsbereit“.__  ​
 +{{ :​information_for_astronomers:​user_guide:​tutorials:​stop.png?​500 |}}
 +
 +Close IndraWorks and open the controlsystem. Now the program should run.
  
   * __**Other Error**__   * __**Other Error**__
 If the telescope does not function due to a different error, you should contact a technician. If the telescope does not function due to a different error, you should contact a technician.
information_for_astronomers/user_guide/tutorials/4mtelescope.1537260060.txt.gz · Last modified: 2018/09/18 10:41 by schweikert