User Tools
information_for_astronomers:user_guide:xffts
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
information_for_astronomers:user_guide:xffts [2014/11/20 23:38] bwinkel [3. Set the correct MultiFiBa Mode and level the XFFTS] |
information_for_astronomers:user_guide:xffts [2014/11/21 10:40] bwinkel [3. Set the correct MultiFiBa Mode and level the XFFTS] |
||
|---|---|---|---|
| Line 28: | Line 28: | ||
| ^Mode^Channels^IF name^IF range^Bandwidth^Attenuation^Comments^ | ^Mode^Channels^IF name^IF range^Bandwidth^Attenuation^Comments^ | ||
| ^ ^ ^ ^[MHz]^[MHz]^enabled^ ^ | ^ ^ ^ ^[MHz]^[MHz]^enabled^ ^ | ||
| - | |097|8+16|VLBA IF|700-800|100|yes| | | + | |249|8+16|VLBA IF|700-800|100|yes| | |
| |185|8+16|VLBA IF|500-1000|500|yes| | | |185|8+16|VLBA IF|500-1000|500|yes| | | ||
| |128|8+16|Narrowband (SB)|100-200|100|yes| | | |128|8+16|Narrowband (SB)|100-200|100|yes| | | ||
| |033|8+16|Optical|0-2500|2500|no|used for UBB/new K-band| | |033|8+16|Optical|0-2500|2500|no|used for UBB/new K-band| | ||
| - | + | {{:information_for_astronomers:user_guide:xfftsgui.png?500|}}\\ | |
| - | {{:information_for_astronomers:xffts_leveling.png?500|}}\\ | + | |
| //Using the xfftsGUI software, it is easy to level the XFFTS and choose correct multiFiBa modes.// | //Using the xfftsGUI software, it is easy to level the XFFTS and choose correct multiFiBa modes.// | ||
| ==== 4. Checking bandpass shapes ==== | ==== 4. Checking bandpass shapes ==== | ||
| - | {{:information_for_astronomers:xffts_100mhz.png?200|}}{{:information_for_astronomers:xffts_500mhz.png?200|}}{{:information_for_astronomers:xffts_2000mhz.png?200|}}\\ | + | {{:information_for_astronomers:user_guide:fiba_249.png?400|}}{{:information_for_astronomers:user_guide:fiba_185.png?400|}}\\ |
| - | //The XFFTS Monitor (on the xffts vnc) should be used to check the bandpass shapes. The figure shows an example of the 1.3-cm receiver for different bandwidth. At least the general shape should be similar for other receivers. Left: 100 MHz. Middle: 500 MHz. Right: 2 GHz.// | + | {{:information_for_astronomers:user_guide:fiba_128.png?400|}}{{:information_for_astronomers:user_guide:fiba_033.png?400|}}\\ |
| + | //The XFFTS Monitor (on the xffts vnc) should be used to check the bandpass shapes. The figures show examples for different bandwidth. At least the general shape should be similar for all receivers. Top left: VLBA-IF 100 MHz, top right: VLBA-IF 500 MHz, lower left: Narrowband-IF (SB) 100 MHz, and lower right: Optical-IF 2 GHz.// | ||
information_for_astronomers/user_guide/xffts.txt · Last modified: 2014/11/21 10:56 by bwinkel
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
