- Information for Astronomers
- General Topics*
- Gruppen Seiten*
* Log-in required
* Log-in required
This is an old revision of the document!
This system is mainly used for sensitive continuum observations. Be aware, that this band may be influenced by RFI. Hence, the bandwidth should not be too large.
Frequency [GHz] | Channel | Polarisation | Tcal [K] | Tsys [K] | Sensitivity [K/Jy] | SEFD [Jy] | Aperture Eff. [%] | TMB/S [K/Jy] | Main Beam Eff. [%] | FWHM [arcsec] | Last update |
---|---|---|---|---|---|---|---|---|---|---|---|
2.6395 | A/B | LCP/RCP | 2.5 | 17 | 1.5 | 11 | 53 | 2.6 | 58 | 260 | Nov 2012 |
normalized Gain curve (G = A0 + A1·Elv + A2·Elv2) | Observed in | confirmed | ||
---|---|---|---|---|
A0 = 1.0 | A1 = 0.0 | A2 = 0.0 | Feb 2007 | Nov 2012 |
Comments:
RX Name | Wavelength [cm] | Frequency (center) [GHz] | Nr. of Horns |
---|---|---|---|
S110mm | 11 | 2.6-2.68 (2.64) | 1 |
Version: | Comment | ||
1. All Modes (BW: 80 MHz) | Narrow band Continuum + 8 ch. polarimeter | ||
Horn offsets [arcsec] | 19.0, 1593.0 |
Note that the narrow line and VLBA IF channels are usually only available when the specific line version of the receiver was selected. In addition for most receivers with narrow line channels the cables at the patch board need to be connected by the receiver group.
To select different channel numbers in OBSINP, the online plot, or the toolbox the numbers have to be specified like c(1)+c(2) to add channel 1 and 2. E.g. channel 1 and 2 contain the LCP and RCP broadband channels, then "OnlPlot pen='c(1)+c(2)'" or "toolbox use='c(1)+c(2)'" will select these channels. In OBSINP the pen can be directly specified in the receiver selection menu.
Abbreviations:
SB: narrow band channel (Schmalband-Kanal), 100 MHz band width
BB: digital broad band channel (Breitband-Kanal), band width varies for different receivers
VLBA: VLBA IF, 500 MHz band width
BW: band width
TP: total power
11cm SFK single horn receiver (multi channel polarimeter 2.595-2.675GHz) | |||
---|---|---|---|
Channel | IF | Pol. | Comment |
1 | SB | LCP | center=2.595 GHz, BW=10 MHz, TP A |
2 | SB | RCP | center=2.595 GHz, BW=10 MHz, TP B |
3 | SB | cross | center=2.595 GHz, BW=10 MHz, cos AB |
4 | SB | cross | center=2.595 GHz, BW=10 MHz, sin AB |
5 | SB | LCP | center=2.605 GHz, BW=10 MHz, TP A |
6 | SB | RCP | center=2.605 GHz, BW=10 MHz, TP B |
7 | SB | cross | center=2.605 GHz, BW=10 MHz, cos AB |
8 | SB | cross | center=2.605 GHz, BW=10 MHz, sin AB |
9–28 | … | … | continues in 10 MHz steps until |
29 | SB | LCP | center=2.675 GHz, BW=10 MHz, TP A |
30 | SB | RCP | center=2.675 GHz, BW=10 MHz, TP B |
31 | SB | cross | center=2.675 GHz, BW=10 MHz, cos AB |
32 | SB | cross | center=2.675 GHz, BW=10 MHz, sin AB |
the last 4 channels contain the total IF 2.595-2.675 GHz | |||
33 | SB | LCP | center=2.635 GHz, BW=80 MHz, TP A |
34 | SB | RCP | center=2.635 GHz, BW=80 MHz, TP B |
35 | SB | cross | center=2.635 GHz, BW=80 MHz, cos AB |
36 | SB | cross | center=2.635 GHz, BW=80 MHz, sin AB |
BW | nchan | nu | Df | Dv | dv |
---|---|---|---|---|---|
MHz | MHz | kHz | km/s | km/s | |
100 | 32768 | 2600 | 3.1 | 0.352 | 0.408 |